Titanium Rods, Pipes & Plates

Product Details:

AMS 4928 R Titanium (Ti6al4v) Grade-5 Round BarsPure titanium undergoes an allotropic transformation from the hexagonal close-packed alpha phase to the body-centered cubic beta phase at a temperature of 882.5°C (1620.5°F). Alloying elements can act to stabilize either the alpha or beta phase. Through the use of alloying additions, the beta phase can be sufficiently stabilized to coexist with alpha at room temperature. This fact forms the basis for creation of titanium alloys that can be strengthened by heat treating.

Titanium alloys are generally classified into three main categories: Alpha alloys, which contain neutral alloying elements (such as Sn) and/or alpha stabilizers (such as Al, O) only and are not heat treatable; Alpha + beta alloys, which generally contain a combination of alpha and beta stabilizers and are heat treatable to various degrees; and Beta alloys, which are metastable and contain sufficient beta stabilizers (such as Mo, V) to completely retain the beta phase upon quenching, and can be solution treated and aged to achieve significant increases in strength.

Ti 6Al-4V is known as the "workhorse" of the titanium industry because it is by far the most common Ti alloy, accounting for more than 50% of total titanium usage. It is an alpha+beta alloy that is heat treatable to achieve moderate increases in strength.

Ti 6Al-4V is recommended for use at service temperatures up to approximately 350°C (660°F).

 

Ti 6Al-4V wrought products are typically used in either a mill annealed or solution treated and aged condition. Rapid quenching following solution treatment (water quench or equivalent) is important in order to maximize the formation of alpha' martensite phase, which in turn maximizes the aging response. Other heat treatments used on Ti 6Al-4V include stress relieving for formed or welded parts, and beta annealing, which is used for improving damage tolerance.

Ti 6Al-4V, like other titanium alloys, has a high affinity for gases including oxygen, nitrogen and hydrogen. Absorption of oxygen results in the formation of an extremely hard, brittle oxygen-stablized alpha phase layer known as alpha case upon heating in air.

Intermediate and final annealing of Ti 6Al-4V mill products is often performed in a vacuum or inert gas atmosphere to avoid alpha case formation and the associated material loss. Vacuum annealing can also be used to remove excess hydrogen pickup, a process known as vacuum degassing. Parts to be vacuum heat treated must be thoroughly cleaned (see Descaling (Cleaning) Notes).

Ti 6Al-4V offers a combination of high strength, light weight, formability and corrosion resistance which have made it a world standard in aerospace applications.
Applications

Ti 6Al-4V may be considered in any application where a combination of high strength at low to moderate temperatures, light weight and excellent corrosion resistance are required. Some of the many applications where this alloy has been used include aircraft turbine engine components, aircraft structural components, aerospace fasteners, high-performance automotive parts, marine applications, medical devices, and sports equipment.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: chennai

Product Details:

Titanium sheet and plate
Grade 2 Titanium
Grade 2 is the commercially pure titanium used in most of the chemical processing plants and is cold formable. Grade 2 plate and sheet can have ultimate tensile strength at and above 40,000 psi.
Grade 5 Titanium
Grade 5 is the aerospace grade and is not cold formable, so it is used more often when no forming is needed. Grade 5 aerospace alloy will have ultimate tensile strength at and above 120,000 psi.Plate is often used with the goal to get really close to the final dimensions of the part being made. The material is worked to the closest size of the desired part and the grain structure of the finished piece is more homogenous. Titanium sheet is often used as a heat barrier because titanium stops the heat and does not transfer to the rest of the assembly. Titanium plate and sheet have ballistic properties making it great for driver protection in racing.

Product Details:

Titanium Grade 5/Titanium 6AL4V
Ti -6Al-4V is heat treatable and has high strength and ductility along with good weldability and fabricability.
Available forms are seamless pipe, welded pipe, seamless tube, welded tube, bar, wire, sheet, plate, forgings, pipe fittings and flanges.

Product Details:

Exporter,Trader and Supplier of titanium rods, titanium 6al4v rods, titanium grade 2 rods rod pipes, titanium grade 5 rods, titanium commercial grade rods...stainless steel pipes, stainless steel tubes, stainless steel welded pipes, stainless steel welded tubes, carbon steel tubes, carbon steel pipes, alloy steel bars, stainless steel plates, stainless steel

Product Details:

Ti -6Al-4V is heat treatable and has high strength and ductility along with good weld ability and fabric ability

Sheet
ASME SB-265
AMS 4911

Product Details:

Minimum Order : Customer Requirement

Supplier ability : 500 Tons / Tons per week

Payment Terms : L/C , T/T

Material : Titanium Plate Rod

Standard : ASTM / AISI / JIS / DIN / GB

Length : Cutting for customer Requirement

Hot Rolled Stainless Steel plate

Payment : Usually 30% of the amount by T/T as deposit and the balance money show be paid by T/T after got the taxed B/L or L/C.

Product Details:

Titanium Gr2 & Gr5 Flats Ragavendra Engineering we are Manufacturer, Exporter and Supplier of Titanium Alloy Round & Flat Bars. We provide various wide range of Titanium Alloy Round & Flat Bars in grades such as grade 2, grade 5. Titanium Grade 2 Flat Bars can be used for parts requiring strength up to 400 Degree F and oxidation resistance to 600 Degree F. In multiple cold forming operations, intermediate stress relief here is recommended to prevent tearing or other material damage. Titanium Grade 5 Flat Bars is being increasingly utilized for medical applications due to its lightweight, its strength, and its hypoallergenic properties, as titanium is also nickel free. Generally, machining characteristics here are similar to those of austenitic stainless steels.

Product Details:

Nickel Alloy Bars
Ragavendra Engineering we maintain a strategic inventory of nickel round bars, and our nickel products are available in both random and customized sizes. Nickel alloys have a broad range of applications, and are widely used for the processing, transportation, and storage of chemicals while playing major roles in the oil, gas and petrochemical industries. These alloys are prized for their outstanding resistance to oxidation and alkaline substances, and for their excellent durability across a very broad spectrum of temperatures and environmental conditions.

Product Details:

Types:Seamless, Welded.
Material: Titanium Gr2 and Gr5.
Specification:
Tube: OD:80.0-500mm WT: 4.0-50mm L: 10.0-6000mm
Pipe : OD: 0.8-160mm WT:0.5-8.0mm L: 10.0-6000mm

Standards: ASTM B337/338/ ASTM B861/862
APPLICATION: Industrial,Aerospace,Chemical,Sports etc,
Quality and Test: strict Test is indispensable because we must ensure our clients get the best product.
The third part inspection EN 10204 : 3.1 is available (QUALITY CERTIFICATE:9001-2015).
Titanium Tube / Pipe

Additional Information:

• Item Code: TITANIUMTUBE
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: chennai
• Production Capacity: 5
• Delivery Time: READY STOCK

Product Details:

Minimum Order : Customer Requirement

Supplier ability : 500 Tons / Tons per week

Payment Terms : L/C , T/T

Material : Titanium Rod

Standard : ASTM / AISI / JIS / DIN / GB

Length : Cutting for customer Requirement

Hot Rolled Stainless Steel plate

Payment : Usually 30% of the amount by T/T as deposit and the balance money show be paid by T/T after got the taxed B/L or L/C.

Product Details:

Offering Titanium Grade 2 Rods.

Minimum order : Customer requirement
Supplier ability : 500 tons / tons per week
Payment terms : L/C, T/T
Material : Titanium Gr 2 rod
Standard : ASTM / AISI/ JIS/ DIN/ GB
Length : Cutting for customer requirement
Hot rolled stainless steel plate
Payment : Usually 30% of the amount by T/T as deposit and the balance money show be paid by T/T after got the taxed B/L or L/C.

Product Details:

Titanium round bar is a very popular go-to for many products. It requires a much more automated process to make than plate and block, which still involve a manual process. Round bar lends itself to a multitude of products, from fasteners to jewelry.
Titanium round bar is available in most of the almost 40 grades, with the most common being grade 5 and grade 2. The medical field often uses small-diameter round bar for body implantable fasteners and dental appliances. Round bar is made from very small diameters of wire for welding, all the way up to larger diameters (such as the 14″ diameter), used for clutch and flywheels.

Product Details:

Titanium Gr2 And Gr5 RodsRagavendra Engineering offers a huge collection of Grade 5 Titanium Rod, Bars and Wire where our packaging specialists pack these products in best quality material to make sure of their safe transportation. The light weight, corrosion resistance and high strength of Titanium Grade 5 Wire Mesh allow this grade to be used in a lot of applications. Most usually used alloy, Titanium Grade 5 Wires is suggestively sturdier than other commercially pure titanium whereas still holding the same toughness and thermal features (without thermal conductivity).Titanium Grade 5 Bars is the most broadly used titanium alloy of the alpha-plus-beta session, and is as well the most communal of all titanium alloys. Meanwhile, these Titanium Grade 5 Products are also being offered in different sizes and shapes to our customers.

Product Details:

Titanium Pipe & FittingsRagavendra engineering provides the industries finest quality titanium pipe and titanium fittings for clients across a variety of industries. Whether you are looking for seamless titanium pipe or welded pipe, Ragavendra engineering can provide you with the material you need for the job. Ragavendra engineering manufactures titanium pipe spools 6” and below from both seamless (ASTM B-861) and welded (ASTM B-862) pipe, typically in schedules 10s, 40s, and 80s. manufactures sizes 8” and by rolling and welding annealed titanium plate (ASTM B-265) with 100% x-ray (RT) and penetrant testing (PT). Final hydtrostatic test is performed when individual titanium pipe spool is complete.

Product Details:

TITANIUM BAR - ROUNDTitanium round bar is a very popular choice for many products from fasteners to jewelry. The medical field often uses small-diameter round bar for body implantable fasteners and dental appliances. Although titanium is a higher cost alternative to aluminum, it provides a lighter weight material with similar or higher strength.

Product Details:

TITANIUM GR5 FLAT BARRagavendra Engineering offers a huge collection of Grade 5 Titanium Round Bars, where our packaging specialists pack these products in best quality material to make sure of their safe transportation. The light weight, corrosion resistance and high strength of our Titanium Grade 5 Square Bars allow this grade to be used in a lot of applications. Most usually used alloy, these Titanium Grade 5 Flat Bars is suggestively sturdier than other commercially pure titanium whereas still holding the same toughness and thermal features (without thermal conductivity). These Titanium Grade 5 Threaded Bars is the most broadly used titanium alloy of the alpha – plus – beta session, and is as well the most communal of all titanium alloys. Meanwhile, our Titanium Grade 5 Hollow Bars are also being offered in different sizes and shapes to our customers. Although “commercially pure” titanium has acceptable mechanical properties and has been used for orthopedic and dental implants, for most applications of these Titanium Grade 5 Hexagonal Bars is alloyed with small amounts of aluminum and vanadium, typically 6 % and 4 % respectively, by weight. Mechanical properties for fracture critical applications of our Titanium Grade 5 Triangular Bars can be enhanced through processing and heat treatment. These Titanium Grade 5 Bars is resistant to general corrosion but may be quickly attacked by environments that cause breakdown of the protective oxide layer including hydrofluoric (HF), hydrochloric (HCl), sulfuric and phosphoric acids.

Product Details:

Our company is one of the distinguished supplier, trader and wholesaler for stainless steel raw material(ss bars,ss sheet,ss pipes) industrial tools and equipment. We fabricate in compliance with industrial quality standards.

Product Details:

Specifications

1 gr1 gr2 gr3 gr4 gr5 gr7
2 THKx1000mmx2000mm
3 ASTMB265 ASMESB265 ASTMF67 ASTMF136 ASTMB708
4, SGS ,ISO 9001

Titanium sheet

Size(mm):Cold Rolled(thickness: 0.3~4.0mm Width:400~1000mm Length:1000~3000)

Hot Rolled(thickness: 4.1~60.0mm Width:400~3000mm Length:1000~4000)

Standard: ASTM B265,AMS4911,ASTM F67,ASTM F136

Grade: GR1.GR2,GR3,GR5,GR7,GR9,GR12…

MOQ: 5KG Sample is available.

Package: plywood case

Delivery Time: 3 to 5 days,or as your quantity.

Payment: T/T or L/C at sight, Western Union, Paypal

Supply ability: 100 tons/month

Port of shipment: tianjin /shenzhen /shanghai

Specifications

Material: GR1,GR2.GR4,GR5
Standard: ASTM B265,AMS4911,ASTM F67,ASTM F136 Thickness:0.5mm-5mm;
Width: 200mm-1500mm
Length: 500mm-6000mm

Customized is ok for us.

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/P,D/A,Other
• Port of Dispatch: CHENNAI
• Production Capacity: 1 TON PER MONTH
• Delivery Time: 1-3 DAYS
• Packaging Details: AT ACTUAL

Product Details:

Grade 2 Titanium Rod
Titanium Round Rod is a very popular go-to for many products. It requires a much more automated process to make than plate and block, which still involve a manual process. Round Rod lends itself to a multitude of products, from fasteners to jewelry.
Titanium round rod is available in most of the almost 40 grades, with the most common being grade 5 and grade 2. The medical field often uses small-diameter round bar for body implantable fasteners and dental appliances. Round bar is made from very small diameters of wire for welding, all the way up to larger diameters (such as the 14 diameter), used for clutch and flywheels.
The bar, rod and wire products on our titanium stock include CP Grade 1 designed for excellent weldability and impact toughness, CP Grade 2, CP Grade 3 used where corrosion resistance is a major design factor, such as when creating aircraft quality titanium, CP Grade 4, Grade 7 and Grade 11, as well as titanium alloys. Supra Alloys inventory contains 6Al-4V or Grade 5, 6Al-4V ELI or Grade 23, Grade 12, 5Al-2.5Sn, 6Al-2Sn-4Z1-2Mo, 15V-3Cr-3Sn-3Al and many other titanium and titanium alloys bar, rod and wire. All bar is supplied in standard 10-14foot mill random length, except special shipping or customer requirements.

Additional Information:

• Item Code: Titanium
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/P,D/A,Other
• Port of Dispatch: chennai or mumbai

Product Details:

Titanium Gr2 Round Rod
Commercially Pure Titanium Grade 2 has moderate quality and phenomenal frosty framing properties. It gives amazing welding properties and has great resistance to oxidation and consumption. Ragavendra Engineering Corporation is a leading supplier and exporter of Titanium Gr2 Round Bar. We provide Titanium Alloy Gr2 Round Bar as per the requirements of our customers and deliver quality products on time. Titanium Alloy Gr2 Round Bar comes in sizes from 8mm to 300mm.Titanium Alloy Gr2 Round Bars are available in different types such as Titanium Alloy Gr2 Round Bars (ASTM B / ASME SB 166), Titanium Alloy Gr2 Round Bars & Bars Exporter in Chennai, India, Grade 2 Titanium Alloy Round Bars, Titanium Alloy UNS R50400 Round Bars & Bars, Titanium Alloy Gr2 Bright Bar & Rods, Titanium Alloy DIN 3.7035 Round Bars & Rods, Titanium Alloy UNS R50400 Bars, Titanium Alloy Gr2 Polish Bars, Titanium Alloy Gr2 Black Bar, Titanium Alloy Gr2 Forged Round Bar Exporters.

Product Details:

Ragavendra Engineering offers a huge collection of Grade 5 Titanium Round Bars, where our packaging specialists pack these products in best quality material to make sure of their safe transportation. The light weight, corrosion resistance and high strength of our Titanium Grade 5 Square Bars allow this grade to be used in a lot of applications. Most usually used alloy, these Titanium Grade 5 Flat Bars is suggestively sturdier than other commercially pure titanium whereas still holding the same toughness and thermal features (without thermal conductivity). These Titanium Grade 5 Threaded Bars is the most broadly used titanium alloy of the alpha – plus – beta session, and is as well the most communal of all titanium alloys. Meanwhile, our Titanium Grade 5 Hollow Bars are also being offered in different sizes and shapes to our customers. Although “commercially pure” titanium has acceptable mechanical properties and has been used for orthopedic and dental implants, for most applications of these Titanium Grade 5 Hexagonal Bars is alloyed with small amounts of aluminum and vanadium, typically 6 % and 4 % respectively, by weight. Mechanical properties for fracture critical applications of our Titanium Grade 5 Triangular Bars can be enhanced through processing and heat treatment. These Titanium Grade 5 Bars is resistant to general corrosion but may be quickly attacked by environments that cause breakdown of the protective oxide layer including hydrofluoric (HF), hydrochloric (HCl), sulfuric and phosphoric acids.

Product Details:

We supply Titanium flat bar in a range of sections from 6mm to any size you require, all manufactured in accordance with ASTM B348.Titanium flat bar is supplied in 4000mm lengths but can be cut to size on request.We typically supply grade 2 and grade 5 titanium flat bar, but can source any grade / specification you need.Grade 2 Titanium (UNS R05400 | Werkstof Nr. 3.7035)Grade 5 Titanium (ti6al4v | UNS R56400 | Werkstof Nr. 3.7165)Due the wide range of sections we are asked to supply we do not keep a lot of titanium flat bar in stock, however we can quickly cut a variety of sections from the Grade 2 and Grade 5 titanium plate that we do hold in stock.Titanium square bar not available from stock can be sourced from our mill in as little as 10 days as we hold a stock of part finished material ready to be supplied in the size / configuration you require.

Product Details:

Specifications

1 Ti (Min): 99.5%
2 Technique:hot roll
3 Size:(0.3-60)*(>=400)*(>=1000 )mm

Grade 2 titanium sheet metal material

Product detail

 

Specification